Recall Information

Description

Vehicle description: trucks equipped with commercial truck tires that have steel cords in the tire sidewall. The valve stems may have been torn or damaged during assembly and could leak causing sidewall damage.

Safety Risk

If not maintained, could result in a sidewall zipper failure. A zipper failure during inflation of a damaged tire could result in injury to someone near the tire.

Remedy

Dealers will inspect the valve stems for leakage, and will replace both the valve stem and the tire if leakage is present. Owner notification began March 28, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Ford at 1-866-436-7332.

Next Steps

Description

Vehicle description: passenger and sport utility vehicles, pickup trucks, and minivans. Equipped with seat belts supplied by trw. It is possible that the driver's and/or front passenger's outboard seat belt buckle may not fully latch. Ford crown victoria built at st. Thomas assembly plant from 4/17/00 - 5/29/01 mercury grand marquis built at st. Thomas assembly plant from 4/17/00 - 5/29/01. Lincoln town cars built at wixom assembly plant from 3/27/00 - 5/30/01. Lincoln navigators built at michigan truck plant from 4/11/00 - 5/31/01. Ford windstars built at oakville assembly plant from 3/23/00 - 5/30/01. Ford rangers built at twin cities plant from 3/28/00 - 5/30/01, and also at the edison plant from 3/13/00 - 5/25/01. Ford F-150 truck built at norfolk plant from 4/18/00 - 5/25/00; at ontario plant from 5/10/00 - 5/28/01; at kansas city plant from 9/11/99 - 5/25/01; and at cuautitlan plant from 5/16/00 - 6/9/01. Ford super duty F-250, F-350, F-450, and F-550 trucks built at kentucky plant from 4/17/00 - 5/27/01; and at cuautitlan plant from 5/16/00 - 6/19/01. Ford excursions built at kentucky plant from 4/17/00 - 10/2/00. Ford expeditions built at michigan truck plant from 4/11/00 - 5/31/01.

Safety Risk

In the event of a crash, the restraint system may not provide adequate occupant protection, increasing the risk of personal injury to the seat occupant.

Remedy

Dealers will inspect the front outboard seat belt buckles and if the buckle fails the inspection process, it will be replaced. Owner notification began July 25, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Ford at 1-866-436-7332.

Next Steps

Description

On certain heavy duty trucks equipped with 7.3L diesel engines, the camshaft position sensor located on the engine of the vehicle may function intermittently, possibly resulting in an engine stall.

Safety Risk

In the event of an engine stall, a crash could result without warning.

Remedy

Dealers will inspect the sensor and replace it with an improved camshaft position sensor free of charge. The recall began on December 29, 2007. Owners may contact Ford at 1-866-436-7332.

Next Steps

Description

Certain passenger vehicles with four or five doors and originally sold in or currently registered in connecticut, delaware, illinois, indiana, iowa, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, west virginia, wisconsin, and the district of columbia, a build-up of corrosion at the pawl pivot area of the rear door latch can cause a binding condition of the pawl that may affect proper engagement of the pawl into the catch. The occupant may experience difficulty opening or closing a rear door, and eventually the rear door may not latch properly.

Safety Risk

If not latched properly, the door may open while the vehicle is in motion. If an occupant fell out of the vehicle, personal injuries could occur.

Remedy

Dealers will have a lower rocker seal added to the door and have the rear door latches evaluated free of charge. A latch that passes the evaluation will be lubricated to prevent future corrosion. A latch that does not pass the evaluation will be replaced. In addition, a sticker will be affixed to the rear doors advising the owners to use the recommended lubricant. The recall began on March 9, 2005. Owners may contact Ford at 1-866-436-7332.

Next Steps

Description

Ford is recalling model years 1995-2003 windstar, 2000-2003 excursion diesel, 1993-1997 and 1999-2003 F-250 sd through F-550 sd diesel, 1992-2003 E-150 through E-550, 1995-2002 explorer, 1997 and 2002 mercury mountaineer, 1995-1997 and 2001-2003 ranger, and 1994 F53 vehicles equipped with the texas instruments speed control deactivation switch (scds). The scds may leak internally and then overheat, smoke, or burn.

Safety Risk

A vehicle fire could occur with or without the engine running.

Remedy

Ford will notify owners that dealers will install a fused wiring harness in line with the scds. On 1999-2003 windstar vehicles with a leaking scds, dealers will also inspect the ABS control module connector and repair as necessary. Repairs will be completed free of charge. The safety recall began on October 27, 2009. Owners may contact Ford at 1-888-222-2751.

Next Steps

Description

Vehicle description: passenger cars, sport utility vehicles, and light and medium duty pickup trucks. A switch located in the plastic cover of the wiper Motor gear case could malfunction and overheat, potentially resulting in loss of intermittent wiper function, loss of wiper park function, complete loss of wiper function, or ignition of the plastic cover material. Switch malfunction is most likely to occur when the intermittent setting of the wipers is being used, or when snow or ice obstructs the blades from returning to the "parked" position at the bottom of the windshield. These vehicles were built at the following assembly plants: atlanta plant from 2/11/00 through 7/31/00; chicago plant from 2/14/00 through 8/4/00; kansas city plant from 2/26/00 to 9/4/00; kentucky truck plant from 2/18/00 to 8/31/00; michigan truck plant from 2/23/00 through 8/3/00; norfolk plant from 2/21/00 through 7/27/00; wayne stamping and assembly plant from 2/25/00 through 8/15/00; and wixom plant from 2/15/00 through 8/8/00.

Safety Risk

Loss of visibility while driving increases the risk of a crash.

Remedy

Dealers will inspect the date code on the wiper Motor. Motors built with the suspect time frame will have the wiper Motor gear case cover replaced. Owner notification began August 20, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Ford at 1-866-436-7332.

Next Steps

Description

Vehicle description: passenger and sport utility vehicles. The inflator canister in the driver air bag module may have an inadequate weld near the igniter.

Safety Risk

In the event of a vehicle crash, the driver air bag may not deploy as intended, potentially resulting in reduced occupant protection, or a burn injury.

Remedy

Dealers will install a driver air bag module. Owner notification began March 19, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Ford at 1-866-436-7332.

Next Steps

Description

Vehicle description: f-super duty crew cab pickup trucks (F-350 short wheelbase trucks equipped with a 6 3/4' pickup box and dual rear wheels) were built after a change was implemented to delete a clamp, and later a bracket that provided a ground for the fuel filler pipe. The pickup box may not have been properly grounded.

Safety Risk

Without proper grounding, an electrostatic discharge could result during fuel fill up, potentially leading to a fire.

Remedy

Dealers will install a fuel filler pipe ground. Owner notification began March 26, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Ford at 1-866-436-7332.

Next Steps

Campaign:

07E21

Description

Powertrain control module (pcm) recalibration

Next Steps