How do I use MyKey?

How do I use MyKey with my Ford®*?

MyKey allows you to program keys with restricted driving modes to promote good driving habits. You can program the restrictions to all keys except one. Any keys that you did not program are administrator keys or admin keys.

You can use admin keys to create, program, and remove a MyKey.

Using MyKey

Select what you would like to do from the drop-down options below for instructions. If you would like to learn more about MyKey settings, select the first drop-down option.

Learning MyKey Settings

MyKey Standard Settings

Not every vehicle includes the features listed below. If your vehicle has this equipment, you cannot change the following settings when using a MyKey:

  • Seatbelt reminder or Belt-Minder™: MyKey mutes the audio system until drivers, and in some instances, passengers, fasten their seatbelts.
  • Earlier low-fuel warning: The low-fuel warning activates earlier giving you more time to refuel.
  • Certain driver alerts, stability systems, or parking aids: MyKey turns them on automatically. For example, Blind Spot Information System (BLIS) with Cross-Traffic Alert, lane departure warning, or forward collision warning.

    Note: You may be able to turn the lane departure warning feature off, but this feature turns back on automatically with every new key cycle.

  • Restricted touchscreen operation: For example, MyKey may prevent manual navigation destination input while the vehicle is in any gear other than park (P) or when the vehicle reaches a certain rate of speed.
  • Screened radio content: Satellite radio adult content restrictions, if this feature is available in your market.

MyKey Optional Settings

You can configure certain vehicle feature settings when you first create a MyKey. You can also change the settings afterward with an admin key.

Note: Not every feature applies to every vehicle in every market. When they are available for your vehicle, they will appear in your information display, providing choices to switch them on or off, or to select a more specific setting.

  • Various vehicle speed limits so that you cannot exceed certain speeds: The information display shows warnings followed by an audible tone when the MyKey driver reaches the set speed. You cannot override the set speed by fully depressing the accelerator pedal.
  • Various vehicle speed reminders, so you know when your vehicle speed approaches the limits: Warnings appear in your information display and a tone sounds when you exceed the set vehicle speed.
  • Audio system's maximum volume limits to 45%: MyKey drivers can concentrate on the road. A message appears in the information display when you attempt to exceed the limited volume. MyKey also disables the automatic volume control.
  • Always On setting: This setting forces certain features to remain on and active. For example, E911 or emergency assistance and the do not disturb features stay on even if you use the feature's control to switch it off. When selected, you will not be able to turn off Advance Trac or traction control, if equipped.

Creating a MyKey

To make a MyKey:

  1. Choose which of your keys will become your MyKey. The other will become an administrator key.
  2. Insert the key you want to program into the ignition. If your vehicle is equipped with a push-button start, place the intelligent access key fob into the backup slot.
  3. Start your vehicle.
  4. Create a MyKey using:
    • The information display.
      1. Tap Settings.
      2. Select MyKey.
      3. Press Create MyKey.
      4. Hold the OK button until you see a message prompting you to label the key as a MyKey.
    • Your vehicle's SYNC screen (if equipped).
      1. Tap Settings.
      2. Choose Vehicle.
      3. Press MyKey.
      4. Select Create MyKey.
  5. Turn off your vehicle. The key will be restricted the next time it is used to start the vehicle.

Note: Make sure to label the MyKey so you can distinguish it from the admin keys.

Programming a MyKey

You can configure some vehicle feature settings when you first create a MyKey. You can also change the settings afterward with an admin key.

To program a MyKey:

  1. Switch the ignition on using an admin key.
  2. Tab through the information display using the OK or the > button on the steering wheel:
    1. Tap Settings.
    2. Press MyKey.
    3. Make your selections.
  3. Turn off the engine and remove the key fob. The programmed restrictions apply when you turn off the vehicle, open and close the driver's door, and restart your vehicle with the programmed key.

Notes:

  • All MyKeys are programmed to the same settings. They cannot be programmed individually.
  • MyKey functionality may vary with some models. Refer to your Owner's Manual for information specific to your vehicle. 
  • For vehicles equipped with a push-button start, when both a MyKey and an admin key are present, the vehicle will defer to the admin key's settings when switching on the vehicle.

Clearing MyKey Settings

You can use the information display or your vehicle's SYNC®** screen (if equipped) to clear your MyKey settings.

Important: 

  • You can clear or change your MyKey settings as long as you do not turn off the vehicle after you create the MyKey.
  • Once you turn the vehicle off, you will need an admin key to change or clear your MyKey settings. If you do not have an admin key, you will need to purchase a new key from your Ford Dealer

Delete a MyKey Using the Information Display

To remove your MyKey settings using the information display:

  1. Turn on your vehicle using an admin key. 
  2. Tab through the message center using the OK or the > button on the steering wheel:
    1. Tap Settings.
    2. Select MyKey.
    3. Press Clear MyKey.
    4. Hold the OK button until you see a message indicating that all MyKeys have been cleared.

Delete a MyKey Using the SYNC Screen

To remove your MyKey settings using the SYNC screen:

  1. Turn on your vehicle using an admin key.
  2. Tap Settings on your vehicle's SYNC screen.
  3. Select Vehicle.
  4. Press MyKey and follow the instructions to clear MyKey. A confirmation message will appear in the display after you finish clearing your MyKeys.

 When you clear your MyKeys, you remove all restrictions and return all MyKeys to their original admin key status. You cannot remove the MyKey restrictions individually.

Additional Information

What do I do if I am having issues with MyKey?


*Driver-assist features are supplemental and do not replace the driver’s attention, judgment, and need to control the vehicle. See your Owner’s Manual for details and limitations.